How to Set up a Tub: Install an Acrylic Tub and Also Bathtub Surround
How to Set up a Tub: Install an Acrylic Tub and Also Bathtub Surround
Blog Article
Right here down the page you'll find more decent points pertaining to How to Install a Bathtub.
Setting up a bath tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the job can move immediately; if you need to open up a wall to get rid of the old tub and place the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the work as well as are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you might require a professional plumber to make tube links.
This short article will aid you install a brand-new tub in your bathroom if you have actually currently gotten a new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your devices and product checklist should consist of the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, put the bathtub in the called for placement. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub until the level checks out level.
To install taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water and examine all joints and also brand-new pipework for leakages as well as tighten them if required. Load the bath tub and also check the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait until the bath tub has actually been utilized a minimum of when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place in between the faucet as well as the sink. Protect the tap in position with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very curious about How to Install a Bathtub and I am assuming you enjoyed the post. Don't hesitate to take a moment to share this blog if you enjoyed reading it. We love reading our article about Tools You Need to Install a New Bathtub .
Call Today
Report this page